NOTE: If you already have side windows click: Fitting Masai windows as replacement for factory-fit side windows
You can fit Masai Panoramic Windows to your Hard Top Land Rover Defender in just a few hours – back on the road the same day, as the special silicone adhesive sticks permanently quite quickly. We do not recommend that you wash your vehicle or leave out in the rain for 24 hours. Fitting windows to a hard top Land Rover Defender is simple if you follow our step by step procedure.
Please watch our video and study the instructions supplied; make sure you have all the tools and other equipment ready before you start, including a table near your vehicle. Please follow widely accepted Safety Precautions, we explain some of them at the foot of this page.
What’s in the Masai Panoramic Windows kit
Your Masai Panoramic Windows kit includes specialist preparation primer and silicone adhesive, an applicator swab for the adhesive, templates and instructions. A pair of Masai Panoramic side windows, and a pair of rear quarter lights – if you bought them too.
The Tools and Equipment You Will Need to Have Ready in Advance:
- A table at least 4 foot long to put the glass on whilst applying the primer and adhesive, if not then use the cardboard box that the windows came in.
- Cloths and mild cleaning agent to make sure all surfaces are clean.
- Latex gloves – the primer and adhesive is difficult to remove if you aren’t careful.
- An electric extension cable.
- An electric drill and an 8mm drill bit for metal.
- Eye and ear protectors when you use the jig saw and drill.
- An applicator gun for use with standard sealant tubes
- A file for taking rough edges off aluminium after you have cut.
- You will need a jig saw and a small blade for cutting thin plate aluminium.
- BluTack or masking tape to hold our template against your vehicle.
- A fine permanent marker pen to mark the cut-out area.
Put the tubes of silicone adhesive in a bucket of hot water (not boiling – ideal is 30 degrees C, 86 F) and get the adhesive applicator gun ready.
Cutting Out The Aperture
Using scissors cut out the window aperture from the template and stick the template to the side of your vehicle with BluTack or masking tape.
Making sure when doing the driver’s side that the template says Off-side or Right side at the top; when doing the passenger side it must say Near-Side or Left Side at the top.
Parallel align the top of the paper template so that it just touches the rim of the roof all along its length.
Using a fine permanent marker pen accurately draw the section to be cut out following the inside edge of the paper template. You can then remove the template and attach it to the other side of your vehicle, flipping it 180 degrees.
Using a drill take the heads off the rivets that hold the two struts inside the vehicle behind the template area, use a mallet to knock the struts sideways and remove them – they won’t be needed any more.
Jig saw practice: Using the drill make a pilot hole somewhere in the middle of the rectangular section you have drawn on your vehicle. Draw a line and a couple of curves to practice cutting along with the jig saw before you start cutting the actual rectangular aperture.
Once you are confident you can cut out the aperture accurately, drill a another pilot hole next to the marked line but within the rectangular marked area – near the chosen place you want to start cutting.
Make sure you are tall enough to reach the top part for cutting – if not get a sturdy box or chair to stand on and be careful.
When you start cutting it is important to follow the marked line as best you can within 1 mm tolerance – do not cut inside the marked area or else you will have a lot of filing to do. Ask someone to hold the other end of the cut-out section steady whilst you finish the final cutting. Lightly file the edges to remove burrs.
You may need someone to also help you offer up the window to make sure it fits in the aperture and aligns parallel and tightly with the roof edge, if it doesn’t you simply file the relevant edges of the aperture so that the window fits neatly in. Repeat this process on the other side of your vehicle.
Preparing The Surfaces And Applying the Adhesive
Clean the outside surfaces of the side of your vehicle surrounding the aperture and also clean the glass. Clean surfaces are important to ensure the primer bonds properly.
Complete one window at a time and decide which side you are doing first – you can tell which window goes on which side as the Masai logo should be the right way up and you need to offer up the windows to see which is which.
Lay the first window on a table, with cardboard or newspaper protection – so that the inside, the aluminium frame side is facing up.
Put on some latex gloves – as the primer and adhesive is very sticky and hard to remove.
TAKE NOTE – You are going to be applying the special primer in a continuous line WITHOUT over-painting what you have done – one stroke only – as it dries very quickly and you may deactivate it if you over-paint.
Shake the preparation primer and CAREFULLY remove the lid.
Don’t use too much or too little primer – use an even amount so there are no really wet parts nor patchy parts (not enough primer on the applicator swab). Wipe the applicator against the inside edge of the primer bottle when with-drawing to ensure there is not too much primer on the applicator that it drips – it sticks very well to all surfaces – so be very careful indeed.
Practice painting a few lines on the section you have cut out, or on another non-important clean, smooth, non-absorbent surface.
Using the applicator apply the primer in neat straight lines along the outer edges of the glass – about 5 mm from the edge, with two extra lines on the larger side and one extra line on the smaller side. Join the lines – no gaps. See photo and video.
Immediately go to the vehicle and apply the primer in the same way – paint the same pattern of lines that you made on the glass around the aperture you are doing first – you are completing one window at a time. Again – join the lines – no gaps. Screw the lid back on the bottle as soon as you are finished.
Immediately get one of the silicone adhesive tubes from the bucket, dry it, insert into gun and remove lid, test on a piece of newspaper to see that the gun is prepared and the adhesive extrudes from the nozzle correctly.
Without delay start to apply the adhesive (see photos) on top of all the lines you have make with the primer on the glass (not the vehicle).
The triangular cut-out in the nozzle needs to face upwards. Make a continuous pyramid shape line along and on top of all of the primer lines (see photo and video). Make sure there are no gaps – particularly the top edge – to ensure no leaks.
Fitting The Windows to The Vehicle
The primer and adhesive application process should be done within 10 – 15 minutes and immediately after carefully carry the window to the vehicle and press it firmly into position.
You will need two people to do this. First priority is to make sure the top edge is parallel to the rim of the roof and the rear side is parallel to the vertical side of the vehicle.
The silicone adhesive bonds straight away to the primer on the vehicle but will take 24 hours to really cure. Keep continuous pressure on all parts of the glass for at least 10 minutes to ensure it is properly stuck evenly all around.
Repeat the whole process with the other side of the vehicle.
You may need to adjust some of the internal trim if necessary to fit around the new window.
Also see: Fitting the Rear Quarter Lights
Safety Precautions
Before embarking on a DIY project, it’s essential that you take the proper safety precautions. Wear protective clothing including safety goggles, gloves, hearing mufflers when working with potentially hazardous materials and equipment such as primers, solvents, adhesives, glass, electric drills and saws. Always use the correct tools for the job. It is worth investing in high quality equipment as this will be safer and will probably do the job quicker.
Don’t rush as you’re more likely to have an accident. Carefully plan the job before you start work. Know your limitations and consult a professional if you are unsure. It’s also a good idea to ask someone if they can help you. Unplug drills and jig saws before fitting parts and remove the chuck key before switching on. We cannot be held responsible if you do not follow safety precautions or do not follow instructions exactly.
